Oil Additives
-
Liqui Moly Brake fluid DOT 4 (Synthetic) 250ml
Liqui Moly DOT 4 brake fluid is ideally suited for use with all disk and drum brake systems, as well as motor vehicle clutch systems for which a synthetic brake fluid is prescribed.
Application:
Liqui Moly DOT 4 brake fluid can be used with all conventional brake fluid bleeding devices. Liqui Moly DOT 4 brake fluid is miscible and compatible with all highquality synthetic brake fluids. The optimal period of use for this brake fluid is, however, only ensured when it is used alone. It is recommended that the brake fluid be changed in accordance with the specifications from the automobile manufacturer.
Areas of Application:
Liqui Moly DOT 4 brake fluid is ideally suited for use with all disk and drum brake systems, as well as motor vehicle clutch systems for which a synthetic brake fluid is prescribed.
Properties:
– miscible and compatible with high
-quality synthetic brake fluids
– outstanding protection against the formation of steam bubbles
– Exceeds the following performance requirements: SAE J 1703, J 1704; ISO 4925; and FMVSS 116
– excellent elastomer compatibility assures a high degree of lubricating action on all moving components in the hydraulic brake circuit
– extremely high wet and dry boiling points
– excellent viscosity/temperature properties
– excellent low temperature behavior
– highest thermal stabilityLiqui Moly Injection Cleaner (300 ml)
For rectifying problems such as difficulties with starting, irregular idling, poor throttle response, performance losses, surges due to lean mixture and poor exhaust values caused by contaminated injection systems. Repeat treatment if problems reoccur. Suitable for all gasoline injection systems.
Application:
One 300 ml can is sufficient for up to 70 liters of fuel. This product is effective over 2,000 km. Injection Cleaner can be mixed with fuel at any time since mixing is spontaneous. One 300 ml can is sufficient for up to 70 liters of fuel. This product is effective over 2,000 km. Injection Cleaner can be mixed with fuel at any time since mixing is spontaneous.Areas of Application:
For rectifying problems such as difficulties with starting, irregular idling, poor throttle response, performance losses, surges due to lean mixture and poor exhaust values caused by contaminated injection systems. Repeat treatment if problems reoccur. Suitable for all gasoline injection systems.Properties:
– cleans the injection system
– Tested for catalytic converters(cc)
– reduces pollutant emissions removes carbon deposits from the intake valves and in the combustion chamber.
– optimum dosage
– cost-effective due to exact dosage
– guarantees low fuel consumptionLiqui Moly Engine Flush (300 ml)
Cleaning and flushing out the oil circuits of gasoline and diesel engines. The use of Engine Flush Plus is dependent on the degree of contamination of the oil circuit. Not suitable for use on motorbikes with wet clutches.
Application:
One 300 ml can is sufficient for up to 6 liters of oil. Add Engine Flush Plus to the motor oil at running temperature before changing the oil. After adding the product, allow the engine to idle for approx. 10 minutes. Then change the oil and the filter. Engine Flush Plus is compatible with all commercially available motor oils.
Areas of application:
Cleaning and flushing out the oil circuits of gasoline and diesel engines. The use of Engine Flush Plus is dependent on the degree of contamination of the oil circuit. Not suitable for use on motorbikes with wet clutches.
Properties:
– optimal engine performance
– highly economical
– tested for turbochargers and catalytic converters
– does not attack common sealing materials
– gentle cleaning
– rapid cleaning
– suitable for diesel particulate filters
– minimizes wearLiqui Moly Windscreen Cleaner Tablet
For windscreen washer systems in both winter and summer use.
Application:
Mix the tab with the windscreen washer water. One tab is sufficient for between 1 and 4 litres of water.
Intended use: For windscreen washer systems in both winter and summer use.
SOLD OUTLiqui Moly Power Steering Leak stop
The additives contained provide optimum care for rubber and plastic seals in the steering gear. Prevents oil loss, stops oil loss in steering gears that drip and regenerates hardened seals. Holes and ducts of the steering gear are cleaned and the performance of the oil is thus revitalized. The noise levels are reduced, the service life is extended and the repair costs are lowered.Suitable for steering gears that are filled with ATF II, ATF III or central hydraulic system oils. Add to the compensating reservoir of the steering system. 35 ml is sufficient for 1 liter of oil.
SOLD OUTLiqui Moly Air Flow Sensor Cleaner
Special active solvent for fast and gentle cleaning of sensitive components of the air flow sensor in gasoline and diesel engines. The Cleaner also distinguishes itself by means of a very fast evaporation that is free of residues. A dirty hot wire or hot plate in the air flow sensor leads to incorrect readings for calculating the fuel/air mixture. The starting and idling properties of the vehicle are thus impaired, the engine performance is reduced and the fuel consumption increases.
Liqui Moly Moterbike Chain Lube 250ml
Initial and maintenance lubrication of power train chains. Especially suitable in dusty, dirty and corrosive atmospheres. For highly-stressed and high-speed chains with and without O-rings.
Properties
- reduces chain elongation
- friction and wear reducing
- resistant to acceleration forces
- excellent adhesion
- especially cold, hot and splash-water resistant
- highest load-carrying capacity
- excellent penetration action
- outstanding corrosion protection
Intended use
Initial and maintenance lubrication of power train chains. Especially suitable in dusty, dirty and corrosive atmospheres. For highly-stressed and high-speed chains with and without O-rings.
Areas of application
Initial and maintenance lubrication of power train chains. Especially suitable in dusty, dirty and corrosive atmospheres. For highly-stressed and high-speed chains with and without O-rings.
Application
Carefully clean chain with solvent such as Motorbike Chain Cleaner (part no. 1602). Apply by spraying. The lubricant attains its final consistency and adherence once the solvent has rapidly evaporated.
WD-40 Specialist Contact Cleaner
- Fast acting, non conductive cleaner
- Penetrates quickly and leaves no residue
- Smart Straw technology for wide area use or more precise usage
- For use on Electrical Equipment, Contacts and much morePlastic and Rubber
Liqui Moly Diesel Purge (500ml)
Used for all diesel engines to prevent and eliminate problems associated with uneven idling and partial load knocking. Quantity to be used for preventive and remedial use 500 ml.
Properties:
– boosts the cetane number
– increases operational reliability
– eliminates diesel knocking
– reduces depositsAreas of Application:
Used for all diesel engines to prevent and eliminate problems associated with uneven idling and partial load knocking. Quantity to be used for preventive and remedial use: 500 ml.Application: Preventive use Add to diesel fuel according to the inspection intervals
Remedial use: Unclip the fuel pipe and immerse the end in the Diesel Flush. Close the fuel return pipe or feed that into the Diesel Flush. Start the engine and allow the engine to run at different speeds with the Diesel Flush unmixed. After the cleaning process, assemble the vehicle’s system. In extreme cases, repeat the cleaning procedure if necessary. As an alternative to remedial procedure, our Jet-Clean Unit can also be used for cleaning. To do this, pour 2-3 litres Diesel Flush into the Jet-Clean tank. Further instructions on use are given in the instructions for the Jet-Clean unit.
– cleans the fuel system
– good corrosion protection
– guarantees optimum combustion
– highly economicalLiqui Moly MOs2 Oil Additive (300 ml)
Added to the lubricating oils of engines, compressors, pumps and especially motor vehicle engines gasoline and diesel. Mixable with all commercially available motor oils.
Application: Add (50 ml per liter of oil) of Oil Additive to motor oil; in motorbikes with a wet clutch add (20 ml per liter of oil). Can be added to motor oil at any time. Shake container before use.
Areas of application:
Added to the lubricating oils of engines, compressors, pumps and especially motor vehicle engines (gasoline and diesel). Mixable with all commercially available motor oils.
Properties:
– reduces oil and fuel consumption
– reduces running-in and operating wear
– no deposits – highest thermal stability
– absolutely compatible with filters
– mixable with all commercially available motor oils
– increases smooth operation
– outstanding emergency
Liqui Moly CERATEC (300 ml)
Cera Tec is a high-tech ceramic wear protection and can be mixed with all commercially available oils. Cera Tec reduces friction and wear by using chemically and thermally extremely high-resilient ceramic compounds. Prevents direct metal/metal contact, increasing the service life of the aggregate. The smooth-running effect reduces fuel consumption in petrol and diesel engines.
Properties
– Reduces frictional losses
– mixable with all commercially available motor oils
– increases smooth operation – highest thermal stability
– excellent high and low temperature behavior
– tested for catalytic converters
– stable under extreme pressures
– compatible with fine filters
– no deposits
– long engine service life
– chemically inert
– reduces fuel consumption
Application:
300 ml is sufficient for up to 5 liters of motor oil. Long-term effect up to 50,000 km. Shake container before use.
WD-40 Specialist High Performance Silicone
- Non-staining, hard working formula which provides excellent lubrication
- Withstands temperatures of -35C to 200C
- Prevents parts from sticking
- Smart Straw technology for wide area use or more precise usage
- For use on Metal, Plastic, Rubber and Wood
WD40
- Cleans: WD-40 gets under dirt, marks and grease making it easy to wipe away. It also dissolves adhesives, allowing easy removal of labels, tape, and stickers
- Protects: WD-40 protects metal surfaces with corrosion-resistant ingredients to shield against moisture and other corrosive elements
- Lubricates: WD-40’s lubricating ingredients are widely dispersed and hold firmly to all moving parts
- Penetrates: WD-40 loosens rust-to-metal bonds and frees stuck, frozen or rusted metal parts
STP OCTANE BOOSTER
BOOSTS OCTANEBOOSTS OCTANE
REDUCES KNOCKING AND PINGINGREDUCES KNOCKING AND PINGING
HELPS RESTORE PERFORMANCEHELPS RESTORE PERFORMANCE
This two-in-one formula boosts octane and cleans the fuel intake system to restore lost performanceSOLD OUTLiqui Moly Radiator Cleaner (300ml)
Suitable for all cooling water systems in motor vehicles, buses and commercial vehicles.
WD-40 Specialist White Lithium Grease Spray
- WHITE LITHIUM GREASE. WD-40 Specialist Protective White Lithium Grease is ideal for metal-to-metal applications that require heavy-duty lubrication and protection against rust and corrosion. Safe from 0° F to 300° F for unbeatable protection
- TASK SPECIFIC SOLUTION. WD-40 Specialist offers easy solutions for specific problems. The WD-40 Specialist line is designed with industrial strength quality and extreme penetration for your hard to solve issues
- METAL-ON-METAL RUST RESISTANT LUBRICANT. Get unbeatable, long lasting protection with this white lithium grease formula. It sprays on easily with a thick, protective coating for auto hinges, gears, sprockets, latches, door tracks, pulleys, cables and more
- REFINED RESULTS. WD-40 Company has been around for over 60 years and has never stopped their innovative mindset. The WD-40 Specialist product line has been refined to perfection so you get the results you need with ease